NEWS
新着情報
Network-M3 ファームウェア 3.0.1 リリース
Network-M3のファームウェア 3.0.1 が公開されました。
※3.x.xにアップグレードしたら、2.x.xへダウングレードできません。
バージョンアップを実施すると、ネットワークカードは再起動しますが、UPS本体は出力を停止することなく稼働し続けます。
以下、Eaton発行のリリースノート（原文）
|
==========================================================================================
Firmware release notes for Eaton Gigabit Network Card for UPS (Network-M3, P/N 744-A4920)
Firmware : Release 3.0.1
Date : 2026/07/29
Eaton (c) 2026
==========================================================================================
===============================
Release 3.0.1 July 2026
===============================
Software compatibility: IPP 1.72 and higher, IPM 2.72 and higher, BLSS 7.0 and higher
Supported UPS: Eaton 5P, 5PX, 5SC Rack, 9PX, 9PXM, 9SX, 9130, FERRUPS FX, 9E, 93PS (fw 2.50->), 91PS, 93E 15-80 EMEA (fw 8.00.01->), 93E G2 EMEA (fw 4.0.20->)
Supported ATS: Eaton EATS115, EATS16, EATS120, EATS220
New Features and Performance
- UPS firmware version display: Added support for displaying the connected UPS firmware version during UPS firmware upgrades.
- Mass Configuration compatibility: Resolved an issue where automation storage requirements prevented successful Mass Configuration operations with Intelligent Power Manager (IPM2).
User Interface
- No user interface changes were introduced in this release.
Security Enhancements
- No security-specific changes were introduced in this release.
Bug Fixes
- Firmware validation: Fixed an issue where attempting to install an incorrect firmware image caused the card to reboot even though the upgrade was rejected.
- Automation ID management: Resolved an issue where deleting an automation or AutoProbe could result in conflicting object IDs.
- 9395XP degraded mode: Fixed an issue that could cause the Industrial Gateway M3 to incorrectly report a degraded state after booting with a 9395XP UPS configuration.
===============================
Release 3.0.0 April 2026
===============================
Software compatibility: IPP 1.72 and higher, IPM 2.72 and higher, BLSS 7.0 and higher
Supported UPS: Eaton 5P, 5PX, 5SC Rack, 9PX, 9PXM, 9SX, 9130, FERRUPS FX, 9E, 93PS (fw 2.50->), 91PS, 93E 15-80 EMEA (fw 8.00.01->), 93E G2 EMEA (fw 4.0.20->)
Supported ATS: Eaton EATS115, EATS16, EATS120, EATS220
New Features and Performance
- Automation Engine: Introduction of an automation engine enabling execution of automation logic.
- Autoprobe capability: card is able to check device response and generate an event that can be used on automation engine.
- Extension of SNMP monitoring data support
-- Addition of UFLS (Under-Frequency Load Shedding)
-- New SNMP objects
- Improved audit logging
User Interface
- Improved usability of menus
- Harmonization of parameter naming in the user interface
Security Enhancements
- Improvements to certificate management, including use of full FQDN (hostname + domain) in certificates
- Updates to secure storage
- Security fixes
Bug Fixes
- Corrections in protocol implementations for SNMP
- Fixes for data logging and export issues
- Improvements in alarm handling and storage
- Fixes and corrections for firmware upgrade, protection script and scheduling behaviors
- Fixes for communication issues with UPS systems
|
Network-M3 ファームウェアアップグレード手順
https://www.daitron.co.jp/eaton/techblog/00427.html